PREPARING A CANVAS FOR WATERCOLOR PAINTING

"Swimmers At The Ledges, Baxter State Park" a watercolor on canvas 16 in. by 20 in. by Michael E. Vermette

How to Prepare a canvas for watercolor painting is a fairly easy method to do. It is an old European formula that many watercolor painters employed including Paul Cézanne. I first discovered this formula from the book: "The Watercolor Handbook, Learning From The Masters" by Ettore Maiotti. This method is a separate method than the heat set Patten used on the market today and is a more traditional formula that uses natural materials. Please use a dust mask when mixing powdered chalks and glues as they can be harmful to your health as with all powdered pigments.

The following are the easy -to-follow steps I use to make my watercolor canvases. Enjoy!

Step 1 : Acquire the art materials and tools.

You will need to stretch a raw unprimed canvas as you always do that does not have a rough texture. Usually a fine tooth canvas is best for watercolor painting. Then you will need cold pressed linseed oil, Kaolin chalk or Chinese White dry pigment, Rabbit Skin glue, a wide 2-inch brush, a double boiler and a stove top or hot plate to heat the mixture, a thermometer and of course water. 

I use Daniel Smith's China Clay, Gamblin's Rabbit Skin Glue and Winsor & Newton's Cold Pressed Linseed Oil.

Step 2: In a double boiler fill the lower half with water and to the upper half add 12 ounces of cold water to 1 ounce of powdered Rabbit Skin Glue (Sometimes referred to as animal glue) in a 1 to 12 proportion ratio. Bring the bottom half to a boil and the upper pot bring no higher than 160 degrees (It is important that you do not boil the mixture or else you will make the ground useless and will have to start over). 

I use a double boiler and a hot plate in my studio and mix the powder and water together with a 2-inch brush. 

I check with a thermometer to make sure I do not go over 160 degrees. 

Step 3: Then, I shut off the heat and before it's allowed to cool I add the chalk (Kaolin or China Clay) to the mixture. You add the chalk until the mixture is the consistency of yogurt. Then I measure out two spoonfuls of Cold Pressed linseed oil for every cup of solution. I warm up the oil a little on low heat in a separate cup and then add it to the mixture by stirring it in with my 2-inch brush. 

When the mixture covers your finger so that you can not see your pink flesh color coming through than you have successfully made the mixture. Next I allow to cool a little before application. 

Step 4: The last step is application. I apply the ground painting the edges first than from side to side horizontally. Then I allow the canvas to dry for about four hours or overnight. Then I heat up and stir the mixture again an apply a second coat vertically crisscrossing the application direction. This mixture will dry faster within a half hour and then you can apply a third coat if you wish. I shouldn't think that more than 3 coats are needed. I am usually satisfied with two coats.

 

You will know when the canvas is fully dry. The wet chalk ground is darker and the canvas when fully dry becomes a brighter bone white.

When it is fully dry, you may begin to paint on the surface with watercolors doing all the things you would normally do on watercolor paper. The difference is, you can lift out a lot easier back to the white ground. The other advantage I found is that there is more control with wet into wet blending and with unexpected water blooms.

After the watercolor painting is completed I usually spray the painting using a Krylon UV protective spray. After it dries I frame it like I would and oil painting on its stretcher. I hope this has helped. Have fun trying this if it's your first experiment with it!

"Approaching Storm over Taos Mountain, Taos New Mexico" a watercolor on canvas 16 in. x 20 in. by Michael E. Vermette

If you would like Michael E. Vermette to demonstrate this process please contact him at 207-827-7573 or e-mail: [email protected].